MAINTENANCE
TIGHTENING TORQUE SPECIFICATIONS
4-15
TIGHTENING TORQUE SPECIFICATIONS
4
TIGHTENING TORQUE LIST
4
CAUTION
If nuts, bolts, or other parts are not tightened to the specified torque, it will cause looseness or damage to
the tightened parts, and this will cause failure of the machine or problems with operation.
Always pay careful attention when tightening parts.
Unless otherwise specified, tighten the metric nuts and bolts to the torque shown in the table below.
If it is necessary to replace any nut or bolt, always use a Komatsu genuine part of the same size as the part that
was replaced.
Apply the following table for Hydraulic Hose.
Thread
diameter
of bolt
(a)(mm)
Width
across
flats
(b)(mm)
Tightninig torque [N·m (kgf·m)]
Target value
Permissible range
6
8
10
12
14
10
13
17
19
22
13.2 (1.35)
31 (3.2)
66 (6.7)
113 (11.5)
177 (18.0)
11.8 - 14.7 (1.2 - 1.5)
27 - 34 (2.8 - 3.5)
59 - 74 (6.0 - 7.5)
98 - 123 (10.0 - 12.5)
157 - 196 (16.0 - 20.0)
16
18
20
22
24
24
27
30
32
36
279 (28.5)
382 (39.0)
549 (56.0)
745 (76.0)
927 (94.5)
245 - 309 (25.0 - 31.5)
343 - 425 (35.0 - 43.5)
490 - 608 (50.0 - 62.0)
662 - 829 (67.5 - 84.5)
824 - 1030 (84.0 - 105.0)
27
30
33
36
39
41
46
50
55
60
1320 (135.0)
1720 (175.0)
2210 (225.0)
2750 (280.0)
3280 (335.0)
1180 - 1470 (120.0 - 150.0)
1520 - 1910 (155.0 - 195.0)
1960 - 2450 (200.0 - 250.0)
2450 - 3040 (250.0 - 310.0)
2890 - 3630 (295.0 - 370.0)
42
65
3830 (390.0)
3430 - 4220 (350.0 - 430.0)
Nominal - No.
of threads (a)
Width
across flats
(b) (mm)
Tightening torque
Target value
Permissible range
N
·
m
kgf
·
m
N
·
m
kgf
·
m
9/16 -18UNF
19
44
4.5
35 - 63
3.5 - 6.5
11/16 -16UN
22
74
7.5
54 - 93
5.5 - 9.5
13/16 -16UN
27
103
10.5
84 - 132
8.5 - 13.5
1 -14UNS
32
157
16.0
128 - 186
13.0 - 19.0
13/16 -12UN
36
216
22.0
177 - 245
18.0 - 25.0
Summary of Contents for Galeo PC800LC-8
