manualshive.com logo in svg

Komatsu 930E-2, Shop Manual

The Komatsu 930E-2 Shop Manual is essential for those seeking to understand and maintain this powerful mining truck. Download this comprehensive manual for free from manualshive.com, providing detailed instructions, diagrams, and maintenance tips to ensure optimal performance and longevity of this remarkable product.

Share
Download
background image

10. Install the check ball in the hole shown in Figure

5-12. Install threaded bushing and lightly tighten.

11. Grease the housing O-ring (3) with Vaseline and

install in the housing groove.

12. Install the distribution plate (15, Figure 5-7) with

plate holes matching the corresponding holes in
the housing.

13. Guide the cardan shaft (11) down into the bore with

the slot in the cardan shaft aligned with the cross
pin (9).

14. Position inner gear wheel onto cardan shaft. It may

be necessary to rotate the gear slightly to find the
matching splines on the cardan shaft. (Splines are
machined  to  insure  proper  alignment  of  cardan
shaft and inner gear wheel.)

15. Grease the O-rings (17 & 18) on both sides of the

outer gear wheel with Vaseline and install.

16. Align outer gear wheel bolt holes with tapped holes

in housing and match marks.

17. Align cover (19) using match marks as a reference

and  install  using  capscrews  (23)  and  washers
(20).

18. Install capscrew with pin (22) into proper hole.

19. Tighten cover capscrews in a criss-cross pattern

to 2 

±

0.4 ft. lbs. (3 

±

0.5 N.m) torque. 

FIGURE 5-12. CHECK BALL INSTALLATION

1. Check Ball hole
2. Check Ball

3. O-Ring
4. Housing

L05021

Steering Control Unit

L5-7

Summary of Contents for 930E-2




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 930E-2

MAFI Trac G Series Operating Manual preview
Trac G Series
Brand: MAFI Pages: 152
Kenworth SmartWheel KM816010 Troubleshooting Manual preview
SmartWheel KM816010
Brand: Kenworth Pages: 45
Kenworth K270 Body Builder'S Manual preview
K270
Brand: Kenworth Pages: 96

Brands by name

Popular brands

Load more brands