background image

1.2

Section 1
Safety and General Information

Carbon Monoxide can cause 
severe nausea, fainting or death.

Do not operate engine in closed or 
confi ned area.

WARNING

Electrical Shock can cause injury.

Do not touch wires while engine is 
running.

CAUTION

Uncoiling Spring can cause severe 
injury.

Wear safety goggles or face 
protection when servicing retractable 
starter.

WARNING

Lethal Exhaust Gases!
Engine exhaust gases contain 
poisonous carbon monoxide. 
Carbon monoxide is odorless, 
colorless, and can cause death 
if inhaled. Avoid inhaling exhaust 
fumes, and never run the engine 
in a closed building or confi ned 
area.

Spring Under Tension!
Retractable starters contain a 
powerful, recoil spring that is 
under tension. Always wear safety 
goggles when servicing retractable 
starters and carefully follow 
instructions in "Retractable Starter" 
Section 7 for relieving spring 
tension.

Explosive Gas!
Batteries produce explosive 
hydrogen gas while being 
charged. To prevent a fi re or 
explosion, charge batteries only in 
well ventilated areas. Keep 
sparks, open fl ames, and other 
sources of ignition away from the 
battery at all times. Keep batteries 
out of the reach of children. 
Remove all jewelry when servicing 
batteries.

Before disconnecting the negative 
(-) ground cable, make sure all 
switches are OFF. If ON, a spark 
will occur at the ground cable 
terminal which could cause an 
explosion if hydrogen gas or 
gasoline vapors are present.

Electrical Shock!
Never touch electrical wires or 
components while the engine is 
running. They can be sources of 
electrical shock.

Explosive Fuel can cause fi res and 
severe burns.

Stop engine before fi lling fuel tank.

WARNING

Explosive Fuel!
Gasoline is extremely fl ammable 
and its vapors can explode if 
ignited. Store gasoline only in 
approved containers, in well 
ventilated, unoccupied buildings, 
away from sparks or fl ames. Do 
not fi ll the fuel tank while the 
engine is hot or running, since 
spilled fuel could ignite if it comes 
in contact with hot parts or sparks 
from ignition. Do not start the 
engine near spilled fuel. Never use 
gasoline as a cleaning agent.

Cleaning Solvents can cause 
severe injury or death.

Use only in well ventilated areas away 
from ignition sources.

WARNING

Flammable Solvents!
Carburetor cleaners and solvents 
are extremely fl ammable. Keep 
sparks, fl ames, and other sources 
of ignition away from the area. 
Follow the cleaner manufacturer’s 
warnings and instructions on its 
proper and safe use. Never use 
gasoline as a cleaning agent.

WARNING

Explosive Gas can cause fi res and 
severe acid burns.

Charge battery only in a well 
ventilated area. Keep sources of 
ignition away.

Summary of Contents for CV11-16























































































































































Reviews: