manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 8

Introduction

8

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

The M-48 SuperMask

®

 has been designed for use with open circuit SCUBA, 

closed, semi-closed circuit SCUBA, and demand mode surface supplied 
diving. Regardless of the diving mode, the mask must be configured for 
the type of system employed.

Because this mask system incorporates several unique design features 
not found in any other full face mask, it is recommended that persons 
with previous full face mask experience make at least one thirty minute 
indoctrination dive prior to open water diving and be completely familiar 
with this user guide. Newly trained divers and divers not experienced in 
full face mask diving should complete a training course in full face mask 
diving combined with a complete understanding of this user guide. Using 
the M-48 SuperMask

®

 is very easy, but as with all new equipment, training 

and practice is the key to enjoyable diving. 

At the surface or while underwater, the pod (lower part) can be effortlessly 
unfastened and resealed to allow:

• 

Clear communication to support personnel

• 

Superior gas conservation before the dive (by breathing 
ambient air)

• 

Alternate gas switching from any demand regulator or 
additional Kirby Morgan

®

 pods

• 

Gas sharing and buddy breathing between divers

All of these actions are accomplished without removing the mask from the 
face and this ultimately reduces task loading and increases diver safety. It is 
as though the diver is simply removing their regulator from their mouth, the 
same as when diving with a traditional SCUBA mask and demand regula-
tor. This makes using the M-48 SuperMask

®

 instinctive to operate even in 

the most complex diving situations. However this said, the user must train 
with the equipment to gain experience in using the mask.

NOTE

The exploded view for the 200-120 Balanced SCUBA regulator 
can be found in its separate user guide, P/N 100-141.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands