manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 28

Donning

28

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

2.  Hold the SuperMask

®

 so that it is hanging from the head harness.

3.  Place the SuperMask

®

 on your head 

in a face down position.  Arrange the 
head harness so that the strap is on 
top of your head and the quick-release 
is against the back of the head and 
neck.  Pull the mask down over the 
face and position the chin into the 
lower section.  

4.  Lightly tighten the top head harness 

straps first, positioning the mask as nec-
essary for a comfortable fit on the face.

5.  Lightly tighten the lower 

head harness straps.  Do 
not over tighten. The mask 
should fit snug, but should 
be comfortable.

Equalizing

The nose cavity of the SuperMask

®

 is used as the method for equalizing. 

Because the actual nose pocket of the mask is very flexible, it allows the 
pocket to be moved slightly in towards the face and can also be flexed 
side to side to get the best possible function for equalizing.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands