manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 33

Donning

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

33

B

 

WARNING

It is important to periodically practice clearing the pod and 

mask in open water. When carrying out these drills is it is 

imperative you train with all of the gear, which you normally 

dive with. Failure to properly train to use this equipment 

can lead to serious injuries or death.

Releasing the Pod from the Mask While Underwater

First, the regulator adjustment knob should be turned in, or detuned. 
Squeeze the front and the back parts of the pod Catch, Release together 
to release the pod from the mask. Swing the pod forward and to the left 
in an arcing motion to free the pod Hook from the mask.

HOOK

BACK CATCH / RELEASE

FRONT

Once the right side of the pod is free, swing the pod to the left allowing it 
to completely unhinge from the mask. 

When removing the pod while using a demand regulator or BOV the 

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands