manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 40

Post Dive Procedures/Checklist

40

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

B

 

WARNING

When purchasing spare parts, always insist on Kirby 

Morgan Genuine Parts. Although other parts may look 

the same, they may not be manufactured to the same 

standards of quality. Improperly manufactured parts can 

cause accidents that can lead to injury or death.

Scheduled Maintenance

This user guide provides properly trained personnel with the guidance and 
technical information needed to perform normal scheduled maintenance 
and adjustments as described herein. Repairs and overhauls must be com-
pleted by M-48 SuperMask

®

 authorized trained technicians.

NOTE

Read and understand each section before attempting the pro-
cedures found in the tables found in the user guide. Refer to the 
accompanying figures for location of callouts included in these 
maintenance steps. Also refer to the parts information included 
in “Exploded View Drawing of the M-48 SuperMask® (No Pod)” 
on page 51.

NOTE

Before scheduled maintenance is performed, all components 
should be thoroughly cleaned in accordance with the procedures 
found in “Cleaning Procedures” on page 37.

Disassembly Guidelines

Routine cleaning and maintenance is the best way to ensure long equip-
ment life and optimum performance. The following outlines scheduled 
maintenance procedures for the M-48 SuperMask

®

.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands