manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 44

Accessories/Spares

44

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

Adjusting Tension on Pod Hook

Over a period of time it might be 
necessary to increase the tension 
on the pod hook found on the left 
hand side of the pod due to mate-
rial fatigue. If two clicks are not 
audible when connecting the pod 
to the mask, it is time to service the 
pod hook.

Begin by exposing the mounting screws by using your finger to gently 
and slightly peel back a portion of the pod silicone skirt on the left side 
to expose the three screws holding the hook to the pod frame. The hook 
has four possible settings and arrives from our factory positioned at the 
optimal setting. 

If adjustment is needed remove the three screws and washers from inside 
the pod frame and remove the pod hook cover found on the outside of the 
assembly. With the hook accessible move the hook one slot closer to the 
front of the pod (away from the mouth). Once it is secured into the new 
slot reinstall the pod hook cover followed by the three screws to finalize 
adjustment.

Accessories/Spares

Prescription Lenses

The following website is available to install prescription lenses onto your 
M-48 mask:

prescriptiondivemasks.com

Inlet Swivel P/N 305-017

The high flow swivel allows the regulator hose to 
move freely and align with the mask without putting 
stress on the hose coupling. It uses standard SCUBA 
threads for incoming breathing air.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands