manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 19

Pre-Dive

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

19

B

 

WARNING

Never dive the pod without a mouthpiece installed in the 

pod. A mouthpiece allows use of the pod even if the pod is 

not sealed to the mask. Buddy breathing cannot be read-

ily accomplished without a mouthpiece installed. Use of 

the mask without the mouthpiece could result in death by 

drowning.

B

 

WARNING

Diving the M-48 SuperMask

®

 without a mouthpiece will 

make dewatering the demand regulator/BOV/DSV more 

difficult. This could lead to death by drowning.

NOTICE

This procedure requires proper tools and a complete un-

derstanding of the installation procedure. Read the pro-

cedure carefully and entirely before attempting to install 

the regulator. If you are not confident you can perform 

this installation correctly, have the work performed by a 

trained technician at an authorized Kirby Morgan dealer.

Tools and Components Needed for 
Installation of Regulator to SCUBA Pod

Needle Nose Pliers or Tie Wrap Gun Rated at 50 lbs./22.6 kg
Side Cutter Pliers
Pliers 
Tie Wrap P/N 520-039 (rated for minimum 50 lb./22.6 kg pull)

1. 

Using the side cutters, cut and remove the tie wrap that secures the 
mouthpiece to your demand regulator/BOV/DSV.

2.  Carefully inspect the regulator/BOV/DSV for sharp edges, and ensure 

the length and dimensions of the mouthpiece mount tube meet the 
requirements as shown previously. Test fit the KMDSI mouthpiece 
P/N 810-022 L to what is being mounted to be certain it will work as 
necessary.

3.  Insert the KMDSI mouthpiece P/N 810-022L from inside the pod; into 

the opening so that the bite end extends into the cavity and the other 
end is flush with the pod opening.

4.  Make certain that both the mouthpiece and regulator mount tube are 

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands