manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 49

Appendix 2 Post-Dive Cleaning and Inspection

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

 

49

Appendix 2 Post-Dive 

Cleaning and Inspection

Kirby Morgan Dive Systems, Inc.

®

1430 Jason Way Santa Maria, California  93455

 Phone:  805/928-7772     Fax:  805/928-0342

www.KirbyMorgan.com   email: kmdsi@KirbyMorgan.com

KI

RBY

 MORGA

N

  D

IV

E SYSTEMS, I

nc

.

© MMXVI Kirby Morgan Dive Systems, Inc.   All Rights Reserved       Document # 160824002 

Page 1 of 1

M-48 Post-Dive Cleaning and Inspection

Diver Name:  

    Date:   

N O.

ST E P

I N I T.

1. 

 

Remove pod from mask. 

2.   

Soapy Solution Wash: Prepare solution of warm water (80–100 °F) and mild hand type dish-
washing soap. Agitate components in solution for 2–3 minutes; use soft bristle brush or clean-
ing rag. Allow mask to soak for 10 minutes then rinse thoroughly with clean fresh water.

3.   

Ensure all debris such as sand and dirt is removed from regulator mouthpiece 
and BOV/DSV inhalation and exhalation ports. Clean the regulator; BOV or DSV 
IAW manufacturer’s instructions. Thoroughly rinse the tilt-to-purge valve.

4.   

Rotate Regulator Adjustment Knob fully out (counter clockwise), if equipped.

5.   

Gently blow dry mask and pod with clean, oil-free low pressure air (less than 30 psig, or 
1.8 bar) or hang and let air dry completely. Allow mask to dry completely before stor-
age. Avoid direct sunlight. To avoid spotting, dry view ports with a clean, lint free cloth.

6.   

Inspect mask for damaged, worn, or missing parts.

7.   

Dry and store mask and pod out of sunlight and fl uores-
cent light, preferably in protective bag or pouch.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands