manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 52

Exploded View Drawing of the M-48 SuperMask® (No Pod)

52

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

1

24

23

3

2

11

12

5

6

14

15

4

16

7

20

5

22

10

15

19

18

9

6

5

8

5

6

7

13

11

6

21

17

11

805-010 SuperMask M-48, 
Black Sides

805-010C SuperMask M-48, 
Clear Sides

Location # Part #

Description

1  

805-031

Harness, semi-stretch

2  

820-225

Strap Keeper

3  

810-005

Mask Skirt

4  

820-050

Lens Retainer

5  

805-028

Buckle Assembly, Non Mag

6  

820-026

Buckle Tab Hold Plug

7  

820-030

Buckle Cap

8  

865-005
865-005C

Lens
Lens, Clear

9  

830-011

Screw

10  

330-205

Washer

11  

820-025

Lock Plug

12  

820-227

Buckle Mount Plate, Left

13  

805-153

Buckle Assembly, Non Mag, Left

14  

820-233

Buckle Cap, Left

15  

830-014

Screw

16  

820-041

Jaw Frame Retainer

17  

820-031

Buckle Cap Retainer

18  

820-045

Pod Catch

19  

820-036

Jaw Frame

20  

820-226

Buckle Mount Plate, Right

21  

805-152

Buckle Assembly, Non Mag, Right

22  

820-232

Buckle Cap, Right

23  

520-038

Tie Wrap

24  

820-155

Comm port plug

NOTE:

 Although some components herein, are labeled, “Non-Mag”, That claim 

is based on tests performed at initial production startup of this mask, and NOT 
based on any ongoing testing. If this product is to be used where the equip-
ment needs to have a low, or non magnetic signature, it is the responsibility of 
the end user to apply any specialized testing, to determine if the equipment 
will pass any needed, low or non magnetic requirements.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands