manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 30

Donning

30

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

3.  Snap the pod catch, release, located on 

the pod, to the right side of the mask 
by positioning your thumb on the back 
of the pod catch (found on the mask) 
and forefinger on the pod catch, release. 
Squeeze the two parts together. Ensure 
that the pod is snapped onto the second 
tooth of the pod catch. A click will be 
heard during the mating procedure.

The pod Catch, Release MUST click and remain on the second and final 
position on the pod catch (on the mask) to be in dive mode.

4.  Insert the mouthpiece and clear the demand regulator or BOV by 

both closing your mouth and pushing the purge button or by force-
fully exhaling into the mouthpiece. If using a DSV exhaling into the 
mouthpiece to clear the regulator is your only option.

5.  Dewater pod - To dewater the pod refer to “Dewatering Basics” on 

page 35

Alternate Method for connecting the Pod

1. 

Place the mouthpiece in your mouth first. Clear the regulator or BOV 
by both closing your mouth and pushing the purge button or by force-
fully exhaling into the mouthpiece. If using a DSV exhaling into the 
mouthpiece to clear the regulator is your only option. 

2.  With the mouthpiece in your mouth, slide the pod to the left to properly 

align the hook onto the mask frame.

3.  Using the thumb and forefinger, snap the pod catch, release closed by 

pinching the front part of the pod catch, release and the back part of 
the pod catch together. Ensure that the pod is snapped onto the sec-
ond tooth of the pod Catch (two clicks) and in the dive mode position. 

4.  Dewater pod - To dewater the pod refer to “Dewatering Basics” on 

page 35.

With either method, you may use your fingers and the palm of your hand 
to snap the pod Catch, Release closed by pinching the front part of the 
Catch, Release and the back part of the pod Catch (mask) together.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands