Maintenance and service
M-7
3)
This item is a quality index of -45 degree dilute antifreeze.
4)
To measure freezing point, should be done in special lab according to SH/T 0090; In emergency,
may adopts portable refractometer to check and the test result is for reference. While existing
disputes to two measuring results, is subject to the SH/T 0090.
5)
To measure PH value, as usual, should be done in special lab according to SH/T 0069.
Fuel recommendation
1.
Diesel oil (only apply to diesel vehicle) : only diesel oil of which cetane value is not less than 45
according to GB252 standard can be used. Sulfur content should not be more than 0.2
％
.
2.
No. 0 light diesel oil: Suitable for the zone where venture rate is 10
％
and minimum temperature is
higher than 4°C.
3.
No.-10 light diesel oil: Suitable for the zone where venture rate is 10 percent and minimum
temperature is more than -5°C.
4.
No.-20 light diesel oil: Suitable for the zone where venture rate is 10 percent and minimum
temperature is more than -14°C.
5.
No.-35 light diesel oil: Suitable for the zone where venture rate is 10 percent and minimum
temperature is more than -29°C.
6.
Natural gas (only apply to Natural Gas Vehicle ):use natural gas of which methane value is low to 65.
Oil quality and specification recommendation
Engine oil
Prefer using the engine oil whose quality is equivalent to or higher than level CH-4 of American
Petroleum Institute API, or refer to the engine specification.
Part of engine oil used for lubricating the piston will be burnt out (consumed) during the engine
running. Engine oil must be replaced in certain period because of high temperature effect and the
oil combustion product interfusing in the oil, especially the chemical additive in the oil will cause
"abrasion" of the oil. This kind of abrasion depends on working condition of engine, quality of
fuel and engine oil; therefore there has different oil changing interval. (Recommended oil changing
interval is 12000km.)
Summary of Contents for XMQ6127 series
