Dometic CLASSIC RM 2620 Installation Instructions Manual Download Page 1

Page: 1 / 54

REVISION

Form No. 3313238.036 7/11

(Replaces 3313238.028)

(French 3313239.034)

LaGrange, IN 46761

RM2351

RM2354

RM2410

RM2451

RM2454

CANADA

Dometic, LLC

48 Zatonski, Unit 3

Brantford, ON N3T 5L8

CANADA

Phone: 519-720-9578

INSTALLATION

INSTRUCTIONS

RM2510

RM2551

RM2554

RM2620

DM2652

DM2662

DM2663

RM3762

RM2820

DM2852

DM2862

RM3962

NDM1062

RM1350

NDA1402

USA

Dometic, LLC

Service Office

2320 Industrial Pkwy.

Elkhart, IN 46516

Phone: 574-294-2511

Corporate Office

2320 Industrial Parkway

Elkhart, IN 46516

For Service Center

Assistance

Call: 800-544-4881

FOR YOUR SAFETY

If you smell gas:
1. Open windows.

2. Don’t touch electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier.

PAR MESURE DE SÉCURITÉ

Si on détecte une odeur de gaz :
1. Ouvrir les fenêtres.

2. Ne pas toucher les commutateurs

électriques.

3. Éteindre toute flamme nue.

4. Contacter immédiatement le fournisseur

de gaz.

FOR YOUR SAFETY

Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

PAR MESURE DE SÉCURITÉ

Ne pas entreposer ou utiliser de l’essence

ou autre vapeur ou liquide inflammable au

voisinage de cet appareil ou de tout autre

appareil ménager.

Improper installation, adjustment,

alteration, service or maintenance can cause

injury or property damage. Refer to this man-

ual. For assistance or additional information

consult a qualified installer, service agency

or the gas supplier.

Une installation, un réglage, une modification,

un dépannage ou un entretien effectués

incorrectement, peuvent provoquer des

blessures ou des dommages matériels.

Se reporter à ce manuel. Pour obtenir une

aide ou des informations complémentaires,

consulter un installateur qualifié, une

entreprise de dépannage ou le fournisseur

de gaz.

AVERTISSEMENT

If the refrigerator stops cooling - or - if

it emits an ammonia smell, immediately

turn the refrigerator off and contact a

Service Center.

Si le réfrigérateur cesse de refroidir - ou - s’il

s’en dégage une odeur d’ammoniac, arrêter

immédiatement le réfrigérateur et contacter

un centre de service après-vente.

AVERTISSEMENT

Summary of Contents for CLASSIC RM 2620























































Search results

Summary of Contents for CLASSIC RM 2620

Reviews:

Related manuals for CLASSIC RM 2620

Brands by name

Popular brands

Dometic CLASSIC RM 2620, Installation Instructions Manual

Search results

Summary of Contents for CLASSIC RM 2620

Reviews:

Related manuals for CLASSIC RM 2620

Brands by name

Popular brands