Dometic CLASSIC RM 2620 Installation Instructions Manual Download Page 3

Page: 3 / 54

- 3 -

CERTIFICATION AND CODE REQUIREMENTS ................................................................................ 4

INSTALLATION PREPARATION ......................................................................................................... 5

VENT APPLICATION TYPES ............................................................................................................ 8

INSTALLATION PROCEDURE ......................................................................................................... 13

REFRIGERATOR REMOVAL ............................................................................................................ 27

APPENDIX A - OVERALL & ROUGH IN DIMENSIONS FOR ENCLOSURE .................................... 28

APPENDIX B - MINIMUM VENTILATION HEIGHTS ........................................................................ 29

APPENDIX C - APPROVED VENTS ................................................................................................. 30

APPENDIX D - VENT INSTALLATION PROCEDURES .................................................................... 34

APPENDIX E - REARVIEW EQUIPMENT ......................................................................................... 35

APPENDIX F - WIRING DIAGRAMS ................................................................................................ 42

CONTENTS

SYMBOLS

The following symbols are used throughout this manual:

This is the safety alert symbol. It is used to alert you to personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury or death.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury.

Information

Step-by-step instructions

Summary of Contents for CLASSIC RM 2620























































Search results

Summary of Contents for CLASSIC RM 2620

Reviews:

Brands by name

Popular brands

Dometic CLASSIC RM 2620, Installation Instructions Manual

Search results

Summary of Contents for CLASSIC RM 2620

Reviews:

Brands by name

Popular brands