manualshive.com logo in svg

Keysight E8663D, User Manual

The Keysight E8663D is a high-performance signal generator designed for precision testing and measurement applications. Ensure optimal use by referring to the User Manual, available for free download from manualshive.com. Conveniently access detailed instructions and specifications to maximize the capabilities of your device.

Share
Download
background image

Contents

Keysight E8357D/67D & E8663D PSG User’s Guide                                                                                      11

Generating a Real Time MSGPS Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Configuring the External Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

Real Time GPS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

Real Time GPS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Setting Up the Real Time GPS Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Configuring the External Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Testing Receiver Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

9. Multitone Waveform Generator

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Creating, Viewing, and Optimizing Multitone Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

To Create a Custom Multitone Waveform  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
To View a Multitone Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
To Edit the Multitone Setup Table  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
To Minimize Carrier Feedthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
To Determine Peak to Average Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258

10.  Two–Tone Waveform Generator

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Creating, Viewing, and Modifying Two–Tone Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263

To Create a Two–Tone Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
To View a Two–Tone Waveform  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
To Minimize Carrier Feedthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
To Change the Alignment of a Two–Tone Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266

11.   AWGN Waveform Generator

Configuring the AWGN Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

Arb Waveform Generator AWGN  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Real Time I/Q Baseband AWGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

12.   Peripheral Devices

N5102A Digital Signal Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Connecting the Clock Source and the Device Under Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
Data Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Operating the N5102A Module in Output Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Operating the N5102A Module in Input Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298

Millimeter-Wave Source Modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307

Using Keysight Millimeter-Wave Source Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Using Other Source Modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309

13.   Troubleshooting

RF Output Power Problems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314

No RF Output Power when Playing a Waveform File (E8267D only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
RF Output Power too Low. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
The Power Supply has Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Signal Loss While Working with a Mixer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315

Summary of Contents for E8663D







































































































































































































































































































































































Reviews:

No comments

Related manuals for E8663D

Oster Versa BLSTVB-103 User Manual preview
Versa BLSTVB-103
Brand: Oster Pages: 21
nedis IREX050BK Quick Start Manual preview
IREX050BK
Brand: nedis Pages: 73
Ninja BLENDER DUO Series Let'S Get Started preview
BLENDER DUO Series
Brand: Ninja Pages: 2
Directed XPRESSKIT GM9 Manual preview
XPRESSKIT GM9
Brand: Directed Pages: 16
H&K PRET 601774 User Manual preview
PRET 601774
Brand: H&K Pages: 11
Vitek VT-1453 Manual Instruction preview
VT-1453
Brand: Vitek Pages: 6
TP-Link TL-WA855RE Quick Installation Manual preview
TL-WA855RE
Brand: TP-Link Pages: 2
Jata hogar HSET1234 Instructions Of Use preview
HSET1234
Brand: Jata hogar Pages: 16
Omcan BL-IT-0075-VT Instruction Manual preview
BL-IT-0075-VT
Brand: Omcan Pages: 28
KING Extend KX2000 User Manual preview
Extend KX2000
Brand: KING Pages: 16
Moulinex CHICAGO User Manual preview
CHICAGO
Brand: Moulinex Pages: 5
HOMCOM 800-104 Assembly & Instruction Manual preview
800-104
Brand: HOMCOM Pages: 32
Gefen CAT5-1600HD User Manual preview
CAT5-1600HD
Brand: Gefen Pages: 11
Aztech WL556E Connecting preview
WL556E
Brand: Aztech Pages: 5
Blendtec Designer Series WildSide Owner'S Manual preview
Designer Series WildSide
Brand: Blendtec Pages: 11
Comnet Copper Line CLFE16EOC Installation And Operation Manual preview
Copper Line CLFE16EOC
Brand: Comnet Pages: 12
Hema 80.08.0004 Instructions For Use Manual preview
80.08.0004
Brand: Hema Pages: 38
Hema 80.08.0015 Instructions For Use Manual preview
80.08.0015
Brand: Hema Pages: 46

Brands by name

Popular brands

Load more brands