Keysight E8663D User Manual Download Page 283

Page: 283 / 358

269

Keysight Technologies
E8357D/67D & E8663D PSG Signal Generators

User’s Guide

11 AWGN Waveform Generator

In the following sections, this chapter contains examples for using the AWGN

waveform generator, which is available only in E8267D vector PSGs with

Options 601 or 602 and Option 403:

—

“Arb Waveform Generator AWGN” on page 270

—

“Real Time I/Q Baseband AWGN” on page 271

For adding real–time AWGN to waveforms using the Dual ARB player, see

“Adding Real–Time Noise to a Dual ARB Waveform (E8267D with Option

403)” on page 109

Summary of Contents for E8663D







































































































































































































































































































































































Search results

Summary of Contents for E8663D

Reviews:

Related manuals for E8663D

Brands by name

Popular brands

Keysight E8663D, User Manual

Search results

Summary of Contents for E8663D

Reviews:

Related manuals for E8663D

Brands by name

Popular brands