Keysight E8663D User Manual Download Page 285

Page: 285 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 271

AWGN Waveform Generator

Configuring the AWGN Generator

Real Time I/Q Baseband AWGN

Press

Preset

Press

Mode

More (1 of 2)

AWGN

Real Time I/Q Baseband AWGN

Press

Band wid th

MHz

Configuring the RF Output

Set the RF output frequency to 500 MHz.

Set the output amplitude to

−

10 dBm.

Press

RF On/Off

Generating the Waveform

Press

AWGN Off On

until On is highlighted.

This generates an AWGN waveform with the parameters defined in the

previous procedure. During waveform generation, the

AWGN

and

I/Q

annunciators activate. The waveform is now modulating the RF carrier.

Summary of Contents for E8663D







































































































































































































































































































































































Search results

Summary of Contents for E8663D

Reviews:

Related manuals for E8663D

Brands by name

Popular brands

Keysight E8663D, User Manual

Search results

Summary of Contents for E8663D

Reviews:

Related manuals for E8663D

Brands by name

Popular brands