Keysight Technologies Infiniium MSOV 084A Service Manual Download Page 38

Page: 38 / 164

Infiniium V-Series Oscilloscopes Service Guide

Testing Performance

Connections

Procedure

Preset the power meter.

Ensure that the power sensor is disconnected from any source and zero the

meter.

Connect the power sensor to the power meter's Power Ref connector and

calibrate the meter.

Make the connections to oscilloscope channel 1 as shown in the preceding

connection diagram.

Set up the power meter to display measurements in units of Watts.

NOTE

•

Connect output 1 of the 11667C splitter to the scope channel N input directly using the

11901A adapter and a connector saver, without any additional cabling or adapters.

•

Connect the power sensor directly to output 2 of the power splitter using the 11901C

adapter without any additional cabling or adapters.

•

Connect the microwave cable directly to output 3 of the power splitter using the 11901C

adapter without any additional cabling or adapters.

•

Minimize the use of other adapters.

•

Ensure the connectors are tightened properly to 8 in-lbs (90 N-cm).

Power sensor

cable

Power sensor

E4413A

Power splitter

11667C

11901C adapter

11901A adapter

Microwave cable

Microwave CW

Generator E8257D

Power meter E4418A or

E4419A

connector saver

Oscilloscope

Summary of Contents for Infiniium MSOV 084A





































































































































































Search results

Summary of Contents for Infiniium MSOV 084A

Reviews:

Related manuals for Infiniium MSOV 084A

Brands by name

Popular brands

Keysight Technologies Infiniium MSOV 084A, Service Manual

Search results

Summary of Contents for Infiniium MSOV 084A

Reviews:

Related manuals for Infiniium MSOV 084A

Brands by name

Popular brands