Kathrein CAP 650 GPS Operating Manual Download

Page: 25 / 48

25 of 48

Risk of material damage due to countersunk head screws!

►

Under no circumstances use countersunk head screws for installation (see figure

on the right).

Risk of malfunction and material damage due to overheating!

If the CAP converter is attached to another electrical device, e.g. a TV set, the temperature rise of each

unit in operation can affect the other, thus causing overheating.

►

Before installing the CAP converter on another electrical device, check with the manufacturer of the

device or in the documentation supplied with it whether this is permissible, and if so, what fittings

(screws, etc.) are necessary or can be used.

Using other screws

If because of the installation location or factors associated with it, the

screws supplied cannot be used, refer to the figure on the right when

selecting the screws to be used. The figure shows you the cross-

section area of the screw sockets on the CAP converter. From this, it is

possible to see the characteristics of the screws which can be inserted

into the CAP converter support, e.g. diameter, screw head profiles etc.

5.2.4 Installing the CAP Converter on the Rear Panel of a TV Set

Danger to life due to high voltage!

If the screws penetrate too deeply into the TV set, they may damage it beyond repair and cause the risk of

a fatal electric shock.

►

Before starting any installation work, disconnect all the units concerned from the mains.

►

Before installing the CAP converter, check with the manufacturer of the device or in the documenta-

tion supplied with it whether this is permissible, and if so, what fittings (screws, etc.) are necessary or

can be used.

Material damage and risk of injuries from overheating of the devices and fire!

►

Under no circumstances install the CAP converter between a TV set and a wall support.

►

Installation of the CAP converter on the rear panel of a TV set is permissible only if the TV set is resting

on a stand that is attached in some other way.

Summary of Contents for CAP 650 GPS

















































Search results

Summary of Contents for CAP 650 GPS

Reviews:

Related manuals for CAP 650 GPS

Brands by name

Popular brands

Kathrein CAP 650 GPS, Operating Manual

Search results

Summary of Contents for CAP 650 GPS

Reviews:

Related manuals for CAP 650 GPS

Brands by name

Popular brands