Kantech KT-1 Installation Manual Download Page 33 | Manualshive

Page: 33 / 50

background image

Connecting Reader Units

The KT-1 provides 12 VDC power for card readers. Up to 2 readers can be con-
nected to a KT-1. The distance between the readers and the KT-1 varies by reader
type, please refer to the documentation provided with the reader. Auxiliary outputs
provide visual and/or audible access operation feedback at the controlled door.

One controller can be installed to control the entry of a single door, or two readers
can be installed on a single door and used to control both the entry and exit. Out-
puts OUT1 and OUT2 are extra multipurpose outputs.

Relay Controlled Outputs

The KT-1 provides two relay outputs: RELAY1 and RELAY2. These outputs are open-
collector rated for up to 100 mA each. The KT-1-PCB provides two form C relays:

© Copyright, 2016, all rights reserved

33

«
...
31
32
33
34
35
...
»

Summary of Contents for KT-1



















































Reviews:

No comments

Related manuals for KT-1

Brand: ABB Pages: 2

Brand: Idesco Pages: 11

Brand: B meters Pages: 2

Brand: Valor Pages: 20

Brand: Jandy Pages: 28

Brand: Jands Pages: 6

Brand: Madas Pages: 6

Brand: Madas Pages: 11

Brand: R82 Pages: 89

Brand: Saftronics Pages: 13

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: Yamaha Pages: 2

Brand: Whale Pages: 8

Brand: Tascam Pages: 8

Brand: Lauda Pages: 40

TITAN-TRACKSIDE-3

Brand: Remote Control Systems Pages: 4

Brand: Gardigo Pages: 12

Brand: Yoshitake Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands