Kantech KT-1 Installation Manual Download Page 21 | Manualshive

Page: 21 / 50

background image

System Architecture

Configurations

The KT-1 can be used through various site configurations with EntraPass Special, Cor-
porate and Global Editions. The following configurations are possible:

Applications with EntraPass Special, Corporate Multi-site Gateway and Global Edi-
tion Gateway:

• Over the internet.
• Over RS-485 with a USB-485 or VC-485.

Application with EntraPass Global Edition and a KT-NCC.

• Over the Internet on premises.
• Over RS-485 with a USB-485 or VC-485.

Layout examples of the configurations:

Over the Internet with EntraPass Special and Corporate Editions

with Multi-site Gateway

Note:

KT-1 can be connected to EntraPass using either RS-485 bus (shown) or Eth-

ernet connection.

© Copyright, 2016, all rights reserved

21

«
...
19
20
21
22
23
...
»

Summary of Contents for KT-1



















































Reviews:

No comments

Related manuals for KT-1

Brand: Jetline Pages: 58

Brand: dbx Pages: 52

Brand: Hankscraft Runxin Pages: 58

Brand: VAT Pages: 26

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: ZKTeco Pages: 14

Brand: Ziton Pages: 28

Brand: Unico Pages: 164

Brand: DANIEL Pages: 48

FEBCO 860 Small Series

Brand: Watts Pages: 12

Brand: Bardiani Valvole Pages: 54

Brand: Parker Pages: 478

Brand: Vag Pages: 15

GA Industries 930-DT

Brand: Vag Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands