Kantech KT-1 Installation Manual Download Page 28 | Manualshive

Page: 28 / 50

background image

KT-1 Installation

1 -

Complete each of the required connections on the small board (B) which

mounts on the wall-plate.

2 -

Install the wall-plate (A) to the wall using the two Phillips screws provided.

3 -

Clip board (B) on the wall plate (A).

4 -

Mount the main boards (C) into board (B)

5 -

Mount the cover (D) and secure with one of the Phillips screws provided.

© Copyright, 2016, all rights reserved

28

«
...
26
27
28
29
30
...
»

Summary of Contents for KT-1



















































Reviews:

No comments

Related manuals for KT-1

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: Samson Pages: 73

Brand: Harman Kardon Pages: 25

Brand: Uniss Pages: 21

Brand: jbc Pages: 44

Brand: jbc Pages: 8

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: OJ Electronics Pages: 8

Brand: OJ Electronics Pages: 112

Brand: OJ Pages: 17

Brand: PACH & COMPANY Pages: 4

Brand: National Instruments Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands