Kantech KT-1 Installation Manual Download Page 45 | Manualshive

Page: 45 / 50

background image

Configuring the KT-1 with the KT-Finder

7 -

Enter the IP addresses. See the Entrapass Help Files for more information.

8 -

Select a Protocol (UDP or TCP).

9 -

Change the Port number, if required (not applicable in TCP).

Note:

The port number should only be changed when you have more than one KT-

1 at the same remote site.

10 -

Click OK.

11 -

Repeat the procedure for each KT-1 at this site.

© Copyright, 2016, all rights reserved

45

«
...
43
44
45
46
47
...
»

Summary of Contents for KT-1



















































Reviews:

No comments

Related manuals for KT-1

Brand: B&R Industries Pages: 89

Brand: IBM Pages: 276

Brand: IBM Pages: 32

Brand: IBM Pages: 157

Brand: JENCO Pages: 36

Brand: jcm-tech Pages: 8

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Brand: Paser Pages: 2

Brand: Computer Automation Technology Pages: 55

Brand: Sensitron Pages: 32

Brand: Waeco Pages: 168

Brand: FMS Pages: 108

Brand: GCE Pages: 13

Brand: Leviton Pages: 2

Brand: TECH Pages: 20

Brand: Bang & Olufsen Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands