Kantech KT-1 Installation Manual Download Page 12 | Manualshive

Page: 12 / 50

background image

Compatibility

The KT-1 is compatible with all EntraPass Editions v6.02 and higher:

• EntraPass Special Edition

• EntraPass Corporate Edition
• EntraPass Global Edition with a Multi-site Gateway, Global Gateway, or a KT-NCC

Network Communications Controller

IP Communication Configuration

Web Configuration Page:

The Web Configuration Page can be used to verify and

configure the IP settings of the KT-1. Refer to the

System Architectur

e section of

this guide for further details.

KT-Finder:

The KT-Finder is a stand-alone application that can be used to verify and

configure the IP settings of the KT-1. Refer to the

System Architecture

section of

this guide for further details.

One Door/Two Readers (Entry/Exit)

The KT-1 is a full onboard door access controller.

Example of KT-1 Setup with T.REX

© Copyright, 2016, all rights reserved

12

«
...
10
11
12
13
14
...
»

Summary of Contents for KT-1



















































Reviews:

No comments

Related manuals for KT-1

Brand: zipwake Pages: 12

Brand: Watts Pages: 2

Brand: jbc Pages: 12

Brand: GARAN Pages: 8

Brand: Gamma Vacuum Pages: 25

Brand: Gamma Pages: 28

Brand: Kathrein Pages: 16

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: Fingertips Lab Pages: 15

Brand: C&C Pages: 17

MultiConnect Dragonfly MTQ-MNA1-B01

Brand: Multitech Pages: 45

Brand: Zonex Pages: 16

Brand: FUTABA Pages: 6

Commander Site Controller

Brand: VeriFone Pages: 34

Brand: Casambi Pages: 4

Brand: ICP DAS USA Pages: 6

Brand: Digital View Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands