Kaba PAXOS advance Series Installation Instructions Manual Download Page 7

PAXOS advance IP

 II_PAXOS_V001_20161007_EN 7

Installation Instructions  

Safety and Environment

Safety and Environment

2.1 

Intended use

The locking system Paxos advance is used for locking and releasing the mechanical locking points 

of safe doors and inner compartment locks, which are generally operated manually via a bolt-

work.
The release (open locks) is only executed after entering one or more of the opening codes on 

the input unit. The opening of the lock can also be made dependent on time functions and/or 

external signals.
The locking system Paxos advance must be used only for its intended purpose – blocking and 

releasing mechanical blocking points of the above-mentioned equipment. Any use beyond this is 

deemed to be improper. The manufacturer is not liable for any damages that result from such use.
The locking system Paxos advance is intended solely for use in closed areas.

2.2 

General

Any person entrusted with installing the electronic high-security locking system Paxos advance 

must read and understand these Installation Instructions before starting work.
Knowledge of the contents of the Installation Instructions is a prerequisite for protecting staff 

from dangers, avoiding faulty operation and thus operating the system safely and appropriately.

2.3 

Personnel qualification

All actions described in these Installation Instructions must be performed only by well trained 

and sufficiently qualified personnel. It is assumed that this personnel knows all of the relevant 

internal and external standards and regulations that must be observed during the installation of 

the system.
For safety and warranty reasons, any further work must be performed solely by personnel 

authorised by the manufacturer.
It is assumed that all of the personnel who complete the installation of the electronic high-

security locking system Paxos advance are aware of and will observe the regulations governing 

work safety and accident prevention.

2.4 

Inadmissible equipment modifications

Modifications to the electronic high security locking system Paxos advance

 

are expressly not rec-

ommended and can lead to the loss of warranty and certification (e.g. VdS certification) and affect 

the security of the system.
Defective system components may be replaced only with original parts from your business 

partner and only by authorized personnel.

Summary of Contents for PAXOS advance Series































































Reviews: