– 29 –
ENGLISH
50 Pedal
specification
Type of pedal sensor s selected.
0
: KFL
1 : PFL
-10. Selection of the pedal specifications” p. 47.
0/1
5 0
1
51
Compensation of
solenod-on tmng
of reverse feed
sttchng at the
start of sewng
Compensation of starting the solenoid for reverse feed stitching
when reverse feed sttchng at the start of sewng s performed.
– 36 to 36
(10°)
5 1
1 1
40
52
Compensation of
solenod-off tmng
of reverse feed
sttchng at the
start of sewng
Compensation of releasing the solenoid for reverse feed stitch
-
ng when reverse feed sttchng at the start of sewng s per-
formed.
– 36 to 36
(10°)
5 2
1 3
40
53
Compensation
of solenod-off
tmng of reverse
feed sttchng at
the end of sewng
Compensation of releasing the solenoid for reverse feed stitch
-
ng when reverse feed sttchng at the end of sewng s per-
formed.
– 36 to 36
(10°)
5 3
4
40
55 Foot lft after
thread trmmng
Functon of lftng presser foot at the tme of (after) thread trmmng
0 : Not provded wth the functon of automatc lftng of work-
clamp after thread trmmng
1 : Provded wth the functon of lftng presser foot automat-
cally after thread trmmng
0/1
5 5
1
40
56 Reverse
revoluton to lft
the needle after
thread trmmng
Functon of reverse revoluton to lft the needle at the tme of (af-
ter) thread trmmng
0 : Not provded wth the functon of reverse revoluton to lft
the needle after thread trmmng
1 : Provded wth the functon of reverse revoluton to lft the
needle after thread trmmng
0/1
5 6
1
41
58 Needle bar
home poston
retanng
functon
Needle bar home poston retanng functon
0 : Needle bar home poston retanng functon s dsabled
1 : Needle bar home poston retanng functon s enabled
(holdng force s weak.)
2 : Needle bar home poston retanng functon s enabled
(holdng force s medum.)
3 : Needle bar home poston retanng functon s enabled
(holdng force s strong.)
0 to 3
5 8
0
41
59 Functon of Auto/
Manual change-
over of reverse
feed sttchng at
the start of sewng
Ths functon can specfy the sewng speed of reverse feed
sttchng at the start of sewng.
0 : The speed wll depend on the manual operaton by pedal, etc.
1 :
The speed will depend on the specified reverse feed stitching speed (No. 8).
0/1
5 9
1
41
60 Functon of stop
mmedately after
reverse feed
sttchng at the
start of sewng
Functon at the tme of completon of reverse feed sttchng at
the start of sewng
0 : Not provded wth the functon of temporary stop of the
sewng machne at the tme of completon of reverse feed
sttchng at the start of sewng
1 : Provded wth the functon of temporary stop of the sew-
ng machne at the tme of completon of reverse feed
sttchng at the start of sewng.
0/1
6 0
0
41
61 Needle bar home
poston retanng
tme
Sets the perod of tme n whch the needle bar s retaned at ts
home poston after the sewng machne has stopped.
0 : The functon s dsabled (the needle bar home poston
retanng functon s enabled at all tmes)
100 - 3000 ms
0 : Disabled
100 to 3000
(ms)
6 1
0
41
64
Change-
over speed of
condensaton
stitch or EBT (end
back tack)
Initial speed when starting condensation stitch or EBT
0 to 250
(st/mn)
6 4
5 0
70 Functon of soft-
down of presser
foot
Presser foot s slowly lowered.
0 : Presser foot s rapdly lowered.
1 : Presser foot s slowly lowered.
0/1
7 0
0
42
71
Double reverse
feed sttchng
functon
Effective/ineffective of double reverse feed stitching is changed
over. (to be used only with CP-18)
0 : Ineffectve
1 : Effective
0/1
7 1
1
72 Sewng
machne startup
selectng
functon
Current limit at the startup of sewing machine is specified.
0 : Normal (Current limit is applied during startup)
1 : Rapid (Current limit is not applied during startup)
0/1
7 2
1
73 Retry functon
Ths functon s used when needle cannot perce materals .
0 : Retry functon s not provded.
1 - 10 : Retry functon s provded.
1: Needle-bar returnng force before operatng the
retry functon: 1 (small) - 10 (large)
0 to 10
7 3
1
42
*
74
With/without
thread trmmer
for MF
With/without thread trimmer for MF is selected.
0 : Not provded wth the tread trmmer
1 : Provded wth the thread trmmer
0/1
7 4
0
No
Item
Description
Settng range
Indcaton of functon settng Ref. page
* Do not change the set values with asterisk (
*
) mark as they are functions for maintenance. If the standard set value set at the
time of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
If it is necessary to change the set value, please purchase the Engineer’s Manual and follow the instructions.
