JR ProPo XG11MV, Operation Manual

Page: 17 / 136

15
▋ DSM2▋Binding▋Method
Following is the explanation how to bind the transmitter and receiver, read very carefully.
1) On the receiver, connect the servos and prepare charged
batteries.
※ Note: DO NOT connect the electric motor ESC or start up
the engine before bind setting is completed. The motor
may abruptly start or the engine speed may increase
suddenly, causing serious danger.
2) Next, perform “bind” so that the receiver can recognize
the transmitter ID. Insert the bind plug into the BIND
terminal of the receiver, connect the batteries for the
receiver (or when a switch harness is used, turn ON the
power). Confirm that the receiver LED starts to blink.
The LED continues to blink until the bind process has
finished.
※ For receivers which have a combined bind and battery
port - apply power at any free port on the receiver.
3) While pressing the bind button on the transmitter
module, turn ON the RF output of the transmitter.
Take your finger off the bind button and confirm that the
LED is blinking and then wait for the LED to turn off,
then back on. At this time, the fail-safe function of the
throttle channel is set, so be sure to set the throttle stick
to the lowest speed position.
4) The bind is completed when the LEDs of the transmitter
and receiver become lit solid. If the receiver LED remains
blinking, try the bind procedure again.
5) Turn off the receiver and disconnect the bind plug which
has been inserted in the receiver. Also turn OFF the
transmitter.
6) Connect the servos to the receiver and confirm operation.
After turning ON the power of the transmitter, turn ON
the receiver.
When the receiver LED lights up and the receiver
recognizes the transmitter, operation will start.
Preparation
RX Battery
Charge Connector
BAT
T1
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
AU
X6
RD1231 Receiver
BAT
T2
Insert the connectors,
taking care of the
direction.
BIND PLUG
AUX5
AUX4
AUX3
AUX2
AUX1
AUX7
Bind button
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Check RF status
to be ON
When using a DSM2 module, be sure
to set the modulation type to PPM9
※When using a Gyro, carry out
the connection according to
the Gyro operation manual.
Switch harness
Rudder channel
Elevator channel
Aileron channel
/ Right Aileron(Glider)
Throttle channel
/ Right Aileron(Glider)
Bind plug
This is used during
the bind procedure.
・FLAP(Airplane/Glider)
・PIT.(Helicopter)
・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)
Binding terminal
Bind plug
Connect the
battery to a
spare channel
(such as AUX
channel)
Location of LED light
RX Battery Charge Connector
BAT
T1
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
AU
X6
RD1231 Receiver
BAT
T2
Insert the connectors,
taking care of the
direction.
BIND PLUG
AUX5
AUX4
AUX3
AUX2
AUX1
AUX7
Bind button
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Check RF status
to be ON
When using a DSM2 module, be sure
to set the modulation type to PPM9
※When using a Gyro, carry out
the connection according to
the Gyro operation manual.
Switch harness
Rudder channel
Elevator channel
Aileron channel
/ Right Aileron(Glider)
Throttle channel
/ Right Aileron(Glider)
Bind plug
This is used during
the bind procedure.
・FLAP(Airplane/Glider)
・PIT.(Helicopter)
・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)
Binding terminal
Bind plug
Connect the
battery to a
spare channel
(such as AUX
channel)
Location of LED light
RX Battery Charge Connector
BAT
T1
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
AU
X6
RD1231 Receiver
BAT
T2
Insert the connectors,
taking care of the
direction.
BIND PLUG
AUX5
AUX4
AUX3
AUX2
AUX1
AUX7
Bind button
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Check RF status
to be ON
When using a DSM2 module, be sure
to set the modulation type to PPM9
※When using a Gyro, carry out
the connection according to
the Gyro operation manual.
Switch harness
Rudder channel
Elevator channel
Aileron channel
/ Right Aileron(Glider)
Throttle channel
/ Right Aileron(Glider)
Bind plug
This is used during
the bind procedure.
・FLAP(Airplane/Glider)
・PIT.(Helicopter)
・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)
Binding terminal
Bind plug
Connect the
battery to a
spare channel
(such as AUX
channel)
Location of LED light
RX Battery Charge Connector
BAT
T1
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
AU
X6
RD1231 Receiver
BAT
T2
Insert the connectors,
taking care of the
direction.
BIND PLUG
AUX5
AUX4
AUX3
AUX2
AUX1
AUX7
Bind button
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Check RF status
to be ON
When using a DSM2 module, be sure
to set the modulation type to PPM9
※When using a Gyro, carry out
the connection according to
the Gyro operation manual.
Switch harness
Rudder channel
Elevator channel
Aileron channel
/ Right Aileron(Glider)
Throttle channel
/ Right Aileron(Glider)
Bind plug
This is used during
the bind procedure.
・FLAP(Airplane/Glider)
・PIT.(Helicopter)
・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)
Binding terminal
Bind plug
Connect the
battery to a
spare channel
(such as AUX
channel)
Location of LED light
RX Battery
Charge Connector
BAT
T1
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
Auxiliary channel
AU
X6
RD1231 Receiver
BAT
T2
Insert the connectors,
taking care of the
direction.
BIND PLUG
AUX5
AUX4
AUX3
AUX2
AUX1
AUX7
Bind button
1. Are the transmitter and receiver batteries fully charged?
2. Is the remote antenna securely connected?
3. Is the distance between the transmitter and receiver too close?
4. When the procedure is carried out on the top of a desk or
bench top that is made from metal, the binding procedure
may not be successful.
If the bind process or range check is not successful,
check the following items:
Check RF status
to be ON
When using a DSM2 module, be sure
to set the modulation type to PPM9
※When using a Gyro, carry out
the connection according to
the Gyro operation manual.
Switch harness
Rudder channel
Elevator channel
Aileron channel
/ Right Aileron(Glider)
Throttle channel
/ Right Aileron(Glider)
Bind plug
This is used during
the bind procedure.
・FLAP(Airplane/Glider)
・PIT.(Helicopter)
・GEAR(Airplane)
・GYRO(Helicopter)
・MOTO(Glider)
Binding terminal
Bind plug
Connect the
battery to a
spare channel
(such as AUX
channel)
Location of LED light
弱
受信強 受信強
同軸部分は曲げて
もかまいません。
アンテナ部分は真直ぐ
な状態で設置。
RX
RX
RX
RX
× 間違ったアンテナの設置方向
アンテナに対しての受信方向を表記
電波遮へい素材フレーム
電波遮へい素材の機体表面
受信感度【高】
受信感度【高】
受信感度
【低】
受信感度【高】
RX
RX
※機体外部に出した
アンテナが破損し
ないように、
ご注意く
ださい。
RGケーブル150
※リモートアンテナは、電波の受信及び
送信機にデータ送信を行います。
リモートアンテナの内蔵アンテナ
は、基板の表側に設置されていま
す。内蔵アンテナを遮へい素材側
に設置した場合、受信感度が著し
く悪くなるのでご注意ください。
リモートアンテナ
内蔵アンテナ
▼ 表 面
▲ 裏 面
強 強
弱
RA01T側面図
内蔵アンテナ
基板面
※ジャイロをご使用になる場合
は、ジャイロの取扱説明書に
従い接続してください。
受信機用電池
BIND PLUG
バインドプラグ
センサー
Y ハーネス
スイッチ
ハーネス
SENSOR
センサーを接続するに
はBIND･BATT･SENS端
子にYハーネス（別売）
を接続してください。
コネクタの向きに
十分注意して差し
込んでください
バインド設定時に使用
ラダー
・ 飛行機/グライダー
フラップ(FLAP)
・ ヘリコプター
ピッチ(PIT.)
予備チャンネル
予備チャンネル
予備チャンネル
エレベーター
エルロン
・ グライダー - 右エルロン(RAIL)
スロットル
・ グライダー - 左エルロン(LAIL)
予備チャンネル
予備チャンネル
RG1131B 受信機
[XG7の場合]
バインド出力
画面
LED Lighting Locations
バインド端子
バインドプラグ
バッテリーは
空チャンネル
に接続します。
Troubleshooting
・Is the remaining battery power of the transmitter and
receiver adequate?
・ Is the distance between the transmitter and receiver too
close?
・When the procedure is carried out on the top of a desk
or bench that is made from metal, binding may not be
successful.
Make sure to set fail safe after completion of the binding
After bonding is completed, make sure to set fail safe
using the Fail Safe function on the transmitter and
check to see if the fail safe works properly.
40 meters
[XG7]
ステータスLED
各アンテナを互いに水平に設置すると、単一方
向の受信になるため、受信効率が低下します。
バインド端子
バインドプラグ
バッテリーは
空チャンネル
に接続します。
・ 飛行機 - ギヤ(GEAR)
・ ヘリコプター
ジャイロ感度調整
(GYRO)
・ グライダー
モーター(MOTO)
30