janitza UMG 96 RM-E User Manual And Technical Specifications Download Page 87 | Manualshive

Page: 87 / 126

background image

87

UMG 96RM-E

Battery

The internal clock is fed from the supply voltage.
If the supply voltage fails then the clock is powered
by the battery. The clock provides date and time
information, for the records, min. and max. values
and results, for example.

The life expectancy of the battery is at least 5 years
with a storage temperature of +45°C. The typical life
expectancy of the battery is 8 to 10 years.

The battery is replaced via the battery insert provided
on the rear of the device. Make sure that the correct
type of battery is used and correct polarity is observed
when inserting the battery (positive pole faces the rear
of the device; negative pole faces the front).

See chapter "Changing the battery" for more information.

Firmware update

If the device is connected to a computer via Ethernet,
then the device firmware can be updated via the GridVis
software.

Select a suitable update file (menu

Extras / Update

device

) and the device and the new firmware will

be transferred.

Fig. GridVis firmware update assistant

C

Firmware may NOT be updated via
the RS485 interface.

«
...
85
86
87
88
89
...
»

Summary of Contents for UMG 96 RM-E































































































































Reviews:

No comments

Related manuals for UMG 96 RM-E

Brand: IFM Pages: 2

Brand: Make Noise Pages: 15

Brand: Major tech Pages: 40

Brand: OBDPROG Pages: 8

Brand: DGH Pages: 87

Brand: Wavetronix Pages: 14

Brand: Vigor Equipment Pages: 12

Brand: LEM Pages: 33

Brand: Datakom Pages: 2

Brand: SAT-Kabel Pages: 12

Brand: Sonel Pages: 26

Brand: PICO Pages: 2

Brand: Maico Pages: 2

Brand: Hanna Instruments Pages: 28

Brand: Omega Pages: 4

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brand: LaserLiner Pages: 64

Brand: Omega Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands