janitza UMG 96 RM-E User Manual And Technical Specifications Download Page 95

Page: 95 / 126

UMG 96RM-E

Possible fault

Cause

Remedy

Effective power too large or too
small.

The programmed current transformer
transformation ratio is incorrect.

Read out and program the current transformer
transformation ratio at the current transformer

The current path is assigned to the wrong
voltage path.

Check connection and correct if necessary.

The programmed voltage transformer
transformation ratio is incorrect.

Read out and program the voltage transformer
transformation ratio at the voltage transformer.

An output is not responding.

The output was incorrectly programmed.

Check the settings and correct if necessary.

The output was incorrectly connected.

Check connection and correct if necessary.

"EEE" in the display

See error messages.

"EEE bAt" in the display

Battery capacity is too low

See "Battery control function" and "Replacing
the battery"

No connection with the device.

RS485
- Device address is incorrect.
- Different bus speeds

(Baud rate).

- Wrong protocol.
- Termination missing.

- Adjust the device address.
- Adjust speed (baud rate).

- Select the correct protocol.
- Close bus with termination resistor.

Ethernet
- IP address is incorrect.
- Incorrect addressing mode

- Adjust IP address at the device.
- Adjust the IP address assignment mode

Device still does not work
despite the above measures.

Device defective.

Send the device to the manufacturer for
inspection and testing along with an accurate
fault description.

Summary of Contents for UMG 96 RM-E































































































































Search results

Summary of Contents for UMG 96 RM-E

Reviews:

Related manuals for UMG 96 RM-E

Brands by name

Popular brands

janitza UMG 96 RM-E, User Manual And Technical Specifications

Search results

Summary of Contents for UMG 96 RM-E

Reviews:

Related manuals for UMG 96 RM-E

Brands by name

Popular brands