Isgus Perfect 2020 Operating And Installation Manual Download Page 43

Page: 43 / 52

Error messages 37

Error messages

Any error at the time recorder is indicated by a combination on the display. If the
problem cannot be solved, please contact your local dealer or e-mail us at:

[email protected]

To avoid any confusion with the date, all error messages begin with the letter E.

Display

Reason

What can be done

P-Module, Error in resident
memory.

→

Punching at the recorder

is no longer possible.

Switch unit off and on.

If the error message is still
displayed, the P-Module has
to be changed.

→

Please contact service

technician.

RTC-module, error in real
time clock component.

→

Punching at the recorder

is no longer possible.

Switch recorder off and on.

If the error message is still
displayed, the RTC-module
has to be changed.

→

Please contact service

technician.

Error in synchronization of
the card lift, mechanical
error.

→

Punching at the recorder

is no longer possible.

Switch recorder off and on.

If the error message is still
displayed

→

Please contact service

technician.

Printer head is blocked or
runs hard.

→

A piece of paper may be

pinched in the card
guide.

Switch off recorder.

Remove metal rear cover,
swing-out programming
panel and check card guide,
Switch on unit.

If the error message is still
displayed

→

Please contact service

technician.

Program error

→

can only happen when

the recorder is switched
on.

Switch recorder off and on.

If the error messages is still
displayed, the EPROM has
to be changed.

→

Please contact service

technician.

Summary of Contents for Perfect 2020





















































Search results

Summary of Contents for Perfect 2020

Reviews:

Related manuals for Perfect 2020

Brands by name

Popular brands

Isgus Perfect 2020, Operating And Installation Manual

Search results

Summary of Contents for Perfect 2020

Reviews:

Related manuals for Perfect 2020

Brands by name

Popular brands