Isgus Perfect 2020 Operating And Installation Manual Download | Manualshive

Page: 13 / 52

background image

Time Recorder Installation 7

Select an easily accessible and vibration-free place of installation. The recorder may
only be placed on a stable, slip-resistant surface.

For the stability of the time recorder use the rubber feet included in the set of
accessories. For this purpose clip them on by following the arrow-head indications.

Also use the 3 cover caps for the metal back plate in order to seal the cable leadings.

The power outlet has to be close to the recorder and easily accessible. Lay the
power cable so that access is not obstructed and persons are not endangered.

Warning!

Only use the time recorder with the enclosed power supply both
in case of table operation and of wall mounting. Do not use
extension cords.

Wall Mounting

The PERFECT time recorder is designed for table mounting. However, 120 VAC
power connection and signal control terminals have been provided to meet the
requirements of eventual wall mounting applications.

Installation steps:

1.  Open the time recorder
2.  Remove the metal rear panel
3.  Mount the time recorder on the wall
4.  Connect the power supply
5.  Connect any additional

functions (if required)

6. Getting

Started

The location of the mounting holes
can be traced from the metal back
plate of the time recorder. The metal
back plate can be plugged in with the
plastic housing.

The installation dimensions shown in
the figure on the right are
recommendations which can be
adjusted to the local conditions. The
dimensions apply both for table
operation and for wall mounting.

Fig. 4: Installation dimensions

«
...
11
12
13
14
15
...
»

Summary of Contents for Perfect 2020





















































Reviews:

No comments

Related manuals for Perfect 2020

Brand: Denver Pages: 27

Brand: Kompernass Pages: 3

SONOCLOCK SC 910

Brand: Grundig Pages: 11

Brand: Lathem Pages: 37

Brand: Youshiko Pages: 6

Brand: Geemarc Pages: 2

Brand: Magnavox Pages: 14

CoLorado TIME SYSTEMS Slim Pace Clock

Brand: Playcore Pages: 14

Brand: Gigaware Pages: 10

Brand: Bigben Pages: 50

Brand: Bodet Time Pages: 5

Brand: TFA Pages: 2

Brand: bbluv Pages: 24

SOUND SOOTHER SI735

Brand: Sharper Image Pages: 18

Brand: Hama Pages: 6

Brand: Realtone Pages: 10

Brand: Geevon Pages: 2

Brand: La Crosse Technology Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands