Isgus Perfect 2020 Operating And Installation Manual Download

Page: 30 / 52

24 Programming

Proceeding

Select change-over mode with "

Value range:

00 - 07, 99

Definition:

00 = no change-over

01 = change-over according to CET

- last Sunday in March, 02:00 >> 03:00

- last Sunday in October, 03:00 >> 02:00

02 = change over according to CET

- last Sunday in March, 02:00 >> 03:00

- 4th Sunday in October, 03:00 >> 02:00

03 = change-over according to GMT

- last Sunday in March, 01:00 >> 02:00

- last Sunday in October, 02:00 >> 01:00

04 = change-over according to GMT

- last Sunday in March, 01:00 >> 02:00

- 4th Sunday in October, 02:00 >> 01:00

05 = change-over according to EEZ

- last Sunday in March, 03:00 >> 04:00

- last Sunday in October, 04:00 >> 03:00

06 = change-over according to EEZ

- last Sunday in March, 03:00 >> 04:00

- 4th Sunday in October, 04:00 >> 03:00

07 = change-over according to USA

- 2nd Sunday in March, 02:00 >> 03:00

1st

Sunday in November, 03:00 >> 02:00

99 = change-over freely programmed

)

When selecting code "00" to "07",

continue with step 4

)

When selecting code "99" continue with

step

Confirm selection using "

Only for freely programmed change-over

D1 =

= Change-over from normal- to

daylight saving time >

Date

D1 =

= Change-over from normal- to

daylight saving time >

Time

D1 =

= Change-over from daylight saving to

normaltime

Date

D1 =

= Change-over from daylight saving to

normaltime

Time

D2 = day / hour
D3 = month / minute

Summary of Contents for Perfect 2020





















































Search results

Summary of Contents for Perfect 2020

Reviews:

Related manuals for Perfect 2020

Brands by name

Popular brands

Isgus Perfect 2020, Operating And Installation Manual

Search results

Summary of Contents for Perfect 2020

Reviews:

Related manuals for Perfect 2020

Brands by name

Popular brands