IPX DDK-1200 Installation & Operation Manual Download Page 17

Page: 17 / 108

3.5 Ipxcam SD card Troubleshooting

1. Check if the SD card position is correct or not. Please refer to the manual for the related

information.

2. After powering the Ipxcam on, correctly insert the SD card, and a little icon of "SD" will show up

in the upper-right corner of the monitor screen. If not, it means the device detection has failed.

Please contact your technical support and ignore the following steps.

3. If no cross sign appears beside the "SD" icon, please go on to the next step. If a cross sign

appears, please check the following:

a. Is it really an SD "Memory" Card?

b. Is this SD card formatted in the FAT16 format?

c. Connect the SD card with a PC and test to see whether the PC can read the data or not.

d. Does this SD card still have the capacity for storing data?

e. Is the SD card set to write?

If all the answers are "yes" but the cross sign still persists, please contact your technical support

and ignore the following steps.

4. Please make sure the function of "SD CARD ENABLE" is activated in the ALARM and

SCHEDULE pages if no cross sign appears beside the "SD" icon on the screen.

5. After recording, read the data on the web page of "sdget.htm". If the data cannot be read through

the network, please read it instead in a PC, check the data stored in the " IPXCAM " directory

and contact your technical support regardless of whether there is data or not.

WARNING

1. Performing this troubleshooting process may need a monitor, a PC, a card reader and

some cables.

2. If the SD card is removed while storing or accessing data, the data will be lost.

3. If there is a cross sign beside the "SD" icon, it means the SD card has been inserted into

the Ipxcam but cannot perform its writing function. Possible reasons are:

a. It is not an SD memory card.

b. The SD card is unformatted or formatted in a non-FAT16 or non-FAT12 format.

c. The file system is damaged.

d. The capacity of the SD card is full.

e. The SD card is set to be read only.

Turn off the power before inserting the SD card. Otherwise the unit may shut down.

Summary of Contents for DDK-1200













































































































Search results

Summary of Contents for DDK-1200

Reviews:

Related manuals for DDK-1200

Brands by name

Popular brands

IPX DDK-1200, Installation & Operation Manual

Search results

Summary of Contents for DDK-1200

Reviews:

Related manuals for DDK-1200

Brands by name

Popular brands