IPX DDK-1200 Installation & Operation Manual Download Page 16

Page: 16 / 108

9. If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET

PLEASE", please write down the error messages shown on the screen and inform your

technical support, while ignoring the following steps.

10. Power off the Ipxcam when this update process is finished, then remove the SD card from the

Ipxcam.

11. Reconnect the Ethernet cable to the RJ-45 port if necessary.

12. Power ON the Ipxcam and it will work normally if the entire update procedure goes correctly.

13. Verify the version of the system software.

WARNING

1. Don’t use FAT32 or NTFS or other file formats in step 1.

2. Steps 1 to 3 have to be done on a PC.

3. Make sure the file of UPDATE.BIN is a correct one in step 3, or the Ipxcam will not work

normally after being updated.

4. If the power of the Ipxcam is suddenly lost in step 8, please remove the SD card first and

turn on the Ipxcam next to test its operation. If the Ipxcam remains working normally,

please go back to step 4; otherwise, please inform your technical support.

5. In step 10, if the SD card is not removed and the Ipxcam does not get online as well, the

updating process must be repeated again after rebooting the Ipxcam.

6. Make sure that the SD card is inserted in a correct position in step 5, or the Ipxcam will

suffer permanent physical damage.

7. If the message "CSUM ERROR" appears in step 8, it implies a problem in the file of

UPDATE.BIN.

8. Don’t interrupt the process while the unit is updating itself; proceed with an SD card

not including any system software of the unit, or else the unit will crash.

Summary of Contents for DDK-1200













































































































Search results

Summary of Contents for DDK-1200

Reviews:

Related manuals for DDK-1200

Brands by name

Popular brands

IPX DDK-1200, Installation & Operation Manual

Search results

Summary of Contents for DDK-1200

Reviews:

Related manuals for DDK-1200

Brands by name

Popular brands