IPX DDK-1200 Installation & Operation Manual Download Page 12

Page: 12 / 108

2.3 Flank Panel

-- Right Flank Panel --

-- Left Flank Panel --

1. Lens

Mount:

This Ipxcam is used with either a C or a CS mount lens.

2. ALC

VR:

Iris control VR.

When an auto iris (DC Drive) lens is used, this VR is used to adjust the iris for different

lighting environments. Adjust the VR clock-wise to open the iris and counter-clockwise

to close the iris of the camera.

3. RESET:

Recover to factory default.

4. IRIS:

Auto iris connector.

This camera works with a DC drive auto iris lens. Please refer to the pin assignment

marked on the camera when connecting the auto iris lens.

5. DIP

Switch:

1. AES:

Auto electric shutter.

2. DC IRIS:

Use an auto iris (DC drive)

3. DHCP:

Turn On / Turn Off to use the DHCP protocol. If the switch
points upwards, the device can change the setup of
network function (enable/disable) via the network.

4. STATIC IP:

If the switch points down, the device can’t obtain an IP

address from the DHCP server. This option is needed
to configure the network communication settings.

6. POWER

Indicator:

Indicates the power status of the unit. The green light indicates the

unit is activating. The red light indicates the power is on and the SD card cannot be

removed.

7. LAN

Indicator:

Indicates the LAN status of the unit. The green light indicates the 100

mbps Ethernet network is activating. The red light signals the LAN is data linking.

8. RS-485

Port

The RS-485 communication ports function as connectors when two or

more units are serially connected to an external control device.

5pin MINI USB

Port

The user can

use a USB device cable to connect the Ipxcam to the

USB port on the PC

10. SD CARD Slot:

This is used for system software updating and archiving / accessing

critical images

Summary of Contents for DDK-1200













































































































Search results

Summary of Contents for DDK-1200

Reviews:

Related manuals for DDK-1200

Brands by name

Popular brands

IPX DDK-1200, Installation & Operation Manual

Search results

Summary of Contents for DDK-1200

Reviews:

Related manuals for DDK-1200

Brands by name

Popular brands