IPS VX121P User Manual Download Page 64

Page: 64 / 68

VX121P/151P/171P(-QM57)

User’s manual rev.0.0 (Preliminary)

64 of 68

MU-C656.xxxxxxxxxx r.0.0-EN

9.13 Cleaning the display

Switch power off and detach power cord before cleaning the Panel PC front panel.

Caution
Use of abrasive cleansers or solvents may damage the display
window. Do not scrub or use brushes.

To clean the display window:

•

Disconnect power from the Panel PC at the power source.

•

For best results on touchscreen, use a clean, damp non-abrasive cloth and a

standard glass cleaner but avoid products containing ammonia.

Caution
Spray the window cleaner on the cloth and not directly on Panel PC.

•

Dry the display window with a chamois leather to avoid water spots.

Warning
Do not use alcohol or inflammables to clean the display window or
any part of the Panel PC.

Summary of Contents for VX121P





































































Search results

Summary of Contents for VX121P

Reviews:

Related manuals for VX121P

Brands by name

Popular brands

IPS VX121P, User Manual

Search results

Summary of Contents for VX121P

Reviews:

Related manuals for VX121P

Brands by name

Popular brands