Intel Stratix 10 MX HBM2 IP User Manual Download Page 24

Page: 24 / 43

Your user logic interfaces to the following signals through the top-level

ed_synth.v

module:
•

Clocks:
— Reference clock input for the UIB PLL that generates the clocks for the UIBSS

and the HBM2 DRA.

— Reference clock input to the I/O PLL that generates the core clock that runs

the user AXI4 interface logic.

•

Resets:
—

hbm_0_example_design_pll_ref_clk_clk

—

hbm_0_example_design_wmcrst_n_in_reset_n

—

hbm_only_reset_in_reset

(Not currently supported.)

•

HBM2 Boundary Scan Signals: The example design requires the boundary scan

signals to be connected for successful compilation, however they are not used.

These do not require to be driven actively or placed in the pin placement file. This

applies to the following signals:
— Input signals:

m2u_bridge_cattrip

m2u_bridge_temp[2:0]

m2u_bridge_wso[7:0]

— Output signals:

m2u_bridge_reset_n

m2u_bridge_wrst_n

m2u_bridge_wrck

m2u_bridge_shiftwr

m2u_bridge_capturewr

m2u_bridge_updatewr

m2u_bridge_selectwir

and m2u_bridge_wsi

•

Traffic Generator signals: The example design instantiates one traffic generator

per AXI4 interface, or one Pseudo Channel. The traffic generator drives the AXI4

interface signals in the example design. The status signals are provided as outputs

that you can monitor
— AXI4 interface signals: The user logic interfaces to one AXI4 interface per

Pseudo Channel. Each AXI4 interface provides the signals required to interface

to the Write Address, Write Data, Write Response, Read Address and Read

Data Channels.

— User Side Band Advanced Peripheral Bus (APB) Interface: The HBM2 IP

supports one APB interface per HBM2 Channel. The user side band interface is

not supported in 17.1 and will be supported in a future release.

•

Traffic Generator status signals:
—

tg<channel num>_<Pseudo Channel

num>_status_traffic_gen_pass

—

tg<channel num>_<Pseudo Channel

num>_status_traffic_gen_fail

—

tg<channel num>_<Pseudo Channel num>_traffic_gen_timeout

Related Links

•

Clock Signals

on page 30

•

Reset Signals

on page 31

•

AXI User-interface Signals

on page 32

3 Generating the Intel Stratix 10 MX HBM2 IP

UG-20031 | December 2017

Intel

Stratix

10 MX HBM2 IP User Guide

Summary of Contents for Stratix 10 MX HBM2 IP












































Search results

Summary of Contents for Stratix 10 MX HBM2 IP

Reviews:

Related manuals for Stratix 10 MX HBM2 IP

Brands by name

Popular brands

Intel Stratix 10 MX HBM2 IP, User Manual

Search results

Summary of Contents for Stratix 10 MX HBM2 IP

Reviews:

Related manuals for Stratix 10 MX HBM2 IP

Brands by name

Popular brands