Intel M50CYP2UR Series System Integration And Service Manual Download Page 113

Page: 113 / 162

Intel® Server System M50CYP2UR Family System Integration and Service Guide

113

6.8.4

3.5

”

Drive Carrier Removal

Figure 149. 3

.5”

Drive Removal

Press the button on the drive extraction lever to release it (see Letter A).

Using the lever, pull the carrier from the drive bay all the way out (see Letter B).

6.8.5

3.5”

HDD Drive Assembly

Drive Blank Removal

Drive Removal

Figure 150. 3.

5”

Drive Assembly

–

Drive Blank / Drive Removal

Hold the drive assembly top side down in your right hand.

Using your left hand, gently rotate the bottom edge of the left rail upwards (see Letter A) while at the
same time pushing the drive or drive blank down away from the carrier (see Letter B).

Summary of Contents for M50CYP2UR Series



































































































































































Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands

Intel M50CYP2UR Series, System Integration And Service Manual

Search results

Summary of Contents for M50CYP2UR Series

Reviews:

Related manuals for M50CYP2UR Series

Brands by name

Popular brands