Intel 80331 Design Manual Download Page 62

Page: 62 / 148

Intel® 80331 I/O Processor

Design Guide

PCI-X Layout Guidelines

6.4.16

PCI 66 MHz Mixed Mode Topology

Figure 31

and

Table 23

provide routing details for a topology with embedded devices and PCI

66 MHz slots.

Trace Length 1 TL1: From 80331 signal Ball to first
junction

5.0” maximum

Trace Length TL2 between junctions

0.5” minimum - 3.5” maximum

Trace Length TL_EM1 to TL_EM4 from junction to
embedded devices

2.0” minimum - 3.0” maximum

Length Matching Requirements

No length matching is required among datalines. For
length matching for clocks, refer clock guidelines

Table 8

Number of vias

Four vias maximum

Table 22.

PCI 66 MHz Embedded Table (Sheet 2 of 2)

Parameter

Routing Guideline for AD Bus

Figure 31.

PCI 66 MHz Mixed Topology

Table 23.

PCI 66 MHz Mixed Mode Table (Sheet 1 of 2)

Parameter

Routing Guideline Lower AD Bus

Routing Guideline Upper AD Bus

Reference Plane

Route over an unbroken ground plane

Breakout

5 mils on 5 mils spacing. Maximum length of the breakout is 500 mils.

Motherboard Trace Impedance (microstrip and
stripline)

50 Ohms +/- 15%

TL1

EM1

L_E

EM2

CONN1

TL_A

AD1

Summary of Contents for 80331





















































































































































Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands

Intel 80331, Design Manual

Search results

Summary of Contents for 80331

Reviews:

Related manuals for 80331

Brands by name

Popular brands