IEI Technology NANO-ULT5 User Manual Download Page 97

Page: 97 / 147

NANO-ULT5 SBC

Page 83

5.3.3 Trusted Computing

Use the

Trusted Computing

menu (

BIOS Menu 5

) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).

Advanced

Configuration

Security Device Support

[Disable]

NO Security Device Found

Enables or Disables BIOS

support for security

device. O.S. will not

show Security Device.

TCG EFI protocol and

INT1A interface will not

be available.

----------------------



: Select Screen

↑

↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

BIOS Menu 5: Trusted Computing



Security Device Support [Disable]

Use the

Security Device Support

option to configure support for the TPM.



Disable D

EFAULT

TPM support is disabled.



Enable

TPM support is enabled.

Summary of Contents for NANO-ULT5




















































































































































Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands

IEI Technology NANO-ULT5, User Manual

Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands