IEI Technology NANO-ULT5 User Manual Download Page 95

Page: 95 / 147

NANO-ULT5 SBC

Page 81



All

EFAULT

Enable all cores in the processor package.



Enable one core in the processor package.



Hyper-threading [Enabled]

Use the

Hyper-threading

BIOS option to enable or disable the Intel Hyper-Threading

Technology.



Disabled

Disables the Intel Hyper-Threading Technology.



Enabled D

EFAULT

Enables the Intel Hyper-Threading Technology.



Intel

SpeedStep™ [Enabled]

Use the

Intel

SpeedStep™

option to enable or disable the Intel

SpeedStep

Technology.



Disabled

Disables the Intel

SpeedStep Technology.



Enabled

EFAULT

Enables the Intel

SpeedStep Technology.



C State [Disabled]

Use the

C State

option to enable or disable CPU C state.



Disabled D

EFAULT

Disables CPU C state.



Enabled

Enables CPU C state.

Summary of Contents for NANO-ULT5




















































































































































Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands

IEI Technology NANO-ULT5, User Manual

Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands