IEI Technology NANO-ULT5 User Manual Download Page 22

Page: 22 / 147

NANO-ULT5 SBC

Page 8

Specification

NANO-ULT5

I/O Interface

Audio Connector

1 x Analog audio by 10-pin (2x5) header

Ethernet

2 x RJ-45 GbE port

Keyboard/Mouse

1 x KB/MS by 6-pin (1x6) wafer

Serial Ports

1 x RS-232 by 9-pin (1x9) wafer
1 x RS-422/485 by 4-pin (1x4) wafer

USB Ports

4 x USB 3.1 Gen 2 on rear I/O
2 x USB 2.0 by 8-pin (2x4) header

Front Panel

1 x Power LED and HDD LED connector by 6-pin (1x6) wafer
1 x Power button connector by 2-pin wafer
1 x Reset button connector by 2-pin wafer

LAN LED

2 x LAN link LED connector by 2-pin header

Fan

1 x Smart fan connector by 4-pin (1x4) wafer

SMBus/I

1 x SMBus/I

C connector by 4-pin (1x4) wafer

Storage

2 x SATA 6Gb/s with 5 V SATA power connectors
Optional eMMC

Expansions

1 x M.2 2230 slot (A-key, USB 2.0 + PCIe x2 signals)
1 x M.2 2280 slot (M-key, PCIe x4 + SATA* signal)
1 x Full-size PCIe Mini card slot (PCIe x1 + USB 2.0 signals,
with SIM card socket)
* The NANO-ULT5-C SKU with Intel

Celeron

4305UE CPU

only supports M.2 SSD modules with PCIe interface.

Environmental and Power Specifications

Power Supply

12 V DC input only (AT/ATX support)

Power Connector

1 x Internal power connector by 4-pin (2x2) connector

Power Consumption

[email protected] (Intel® Core™ i7-8665UE CPU with two
16 GB 2666 MHz DDR4 memory modules)

Operating Temperature

-20°C ~ 60°C

Summary of Contents for NANO-ULT5




















































































































































Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands

IEI Technology NANO-ULT5, User Manual

Search results

Summary of Contents for NANO-ULT5

Reviews:

Related manuals for NANO-ULT5

Brands by name

Popular brands