manualshive.com logo in svg

IEI Technology NANO-ULT5, User Manual

Share
Download
IEI Technology NANO-ULT5 User Manual Download Page 16

 

 

NANO-ULT5 SBC 

 

Page 2 

1.1 Introduction 

 

Figure 1-1: NANO-ULT5 

The NANO-ULT5 series is an EPIC form factor single bard computer. It has an on-board 
8

th

  generation  14nm Intel® Core™ i7/i5/i3 or Celeron®  processor,  and supports two 

260-pin 2133/2400 MHz dual-channel DDR4 SDRAM SO-DIMM slots with up to 32.0 GB 
of memory.   

The  NANO-ULT5  series  includes  a  DisplayPort  connector,  a  HDMI connector and an 
18-/24-bit LVDS connector for triple independent display. 

Expansion and I/O include one full-size PCIe Mini slot supporting 3G/4G modules, one 
M.2 A-key slot and one M.2 M-key slot for expansions, four USB 3.1 Gen 2 connectors on 
the rear panel, two USB 2.0 connectors by pin header and two SATA 6Gb/s connectors. 
Serial device connectivity is provided by  one external RS-232  connector, one  internal 
RS-232 connector and one internal RS-422/485 connector. Two RJ-45 GbE connectors 
provide the system with smooth connections to an external LAN. One on-board SIM card 
socket also supports for 3G/LTE expansion. 

 

Summary of Contents for NANO-ULT5




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands