manualshive.com logo in svg

IEI Technology NANO-ULT5, User Manual

Share
Download
IEI Technology NANO-ULT5 User Manual Download Page 133

 

 

NANO-ULT5 SBC 

 

Page 119 

   
DECLARATION OF CONFORMITY 

 

This equipment

 

has been tested and found to comply with specifications for CE marking. 

If the user modifies and/or installs other devices in the equipment, the CE conformity 
declaration may no longer apply. 

 
 
 

FCC WARNING 

 

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 

 

This device may not cause harmful interference, and 

 

This device must accept any interference received, including interference 
that may cause undesired operation. 

 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own expense. 

 

 

Summary of Contents for NANO-ULT5




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands