manualshive.com logo in svg

IEI Technology NANO-ULT5, User Manual

Share
Download
IEI Technology NANO-ULT5 User Manual Download Page 111

 

 

NANO-ULT5 SBC 

 

Page 97 

 

CSM Support [Enabled] 

Use the 

CSM Support

 BIOS option to enable or disable CSM support. 

 

Disabled 

 

CSM support disabled 

 

Enabled 

D

EFAULT

 

CSM support enabled 

5.3.11 NVMe Configuration 

Use the 

NVMe Configuration

 (

BIOS Menu 17

) menu to display the NVMe controller and 

device information. 

Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

NVMe controller and Drive information 

 

No NVMe Device Found 

 

 

 

 

--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter:  Select 

+/-:  Change Opt. 

F1:  General Help 

F2:  Previous Values 

F3:  Optimized Defaults 

F4:  Save & Exit 

ESC: Exit 

Version 2.20.1271. Copyright (C) 2018 American Megatrends, Inc. 

BIOS Menu 17:

 

NVMe Configuration

 

 

Summary of Contents for NANO-ULT5




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands