IEI Technology eKINO-BT User Manual Download

Page: 116 / 157

eKINO-BT Mini-ITX SBC

Page 102

5.3.7 IDE Configuration

Use the

IDE Configuration

menu (

BIOS Menu 12

) to view the SATA devices installed in

the system.

Advanced

IDE Configuration

Serial-ATA (SATA)

[Enabled]

SATA Mode

[IDE Mode]

SATA1
Not Present

SATA2
Not Present

Enable/Disable Serial
ATA

---------------------

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 12: IDE

Configuration

Serial-ATA (SATA) [Enabled]

Use the

Serial-ATA (SATA)

option to enable or disable the serial ATA controller.

Enabled D

EFAULT

Enables the on-board SATA controller.

Disabled

Disables the on-board SATA controller.

SATA Mode Selection [IDE Mode]

Use the

SATA Mode Selection

option to configure SATA devices as normal IDE devices.

IDE Mode

EFAULT

Configures SATA devices as normal IDE device.

AHCI Mode

Configures SATA devices as AHCI device.

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands