IEI Technology eKINO-BT User Manual Download Page 23

Page: 23 / 157

eKINO-BT Mini-ITX SBC

Page 9

Super I/O Controller

Fintek F81866D-I

Embedded Controller

ITE IT8528E

Watchdog Timer

Software programmable, supports 1~255 sec. system reset

Expansions

One full-size/half-size PCIe Mini card slot (with USB 2.0 signal)

One PCIe x1 slot

One CFast card slot

One microSD card slot (E38XX SKU only)

I/O Interface Connectors

Audio Connectors

Line-out and mic-in audio jacks on rear panel

One front panel audio connector (10-pin header)

Battery Connectors

One 2-pin wafer connector

One 12-pin wafer connector (for

AUPS battery)

Digital I/O

One 8-bit digital I/O

Ethernet

Two RJ-45 GbE ports

Fan Connectors

One 4-pin wafer connector (CPU fan)

One 3-pin wafer connector (system fan)

Front Panel

One 14-pin header (power LED, HDD LED, speaker, power button,

reset button)

Keyboard and Mouse

One 6-pin wafer connector for PS/2 keyboard and mouse

LAN LEDs

Two

2-pin headers for LAN1 LED and LAN2 LED (link signal)

Serial ATA

Two SATA 3Gb/s connectors

Two 5 V SATA power connectors

Serial Ports

Four RS-232 COM connectors (one by pin header, three on rear panel)

One RS-422/485 COM connector (4-pin wafer)

SMBus

One 4-pin wafer connector

USB Ports

Two USB 3.0 ports on rear panel

Four USB 2.0 ports (two on rear panel, two by pin headers)

TPM

One 20-pin header

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Brands by name

Popular brands