IEI Technology eKINO-BT User Manual Download

Page: 84 / 157

eKINO-BT Mini-ITX SBC

Page 70

4.7.5 LVDS1 Voltage Selection

WARNING:

Permanent damage to the screen and eKINO-BT may occur if the

wrong voltage is selected with this jumper. Please refer to the user

guide that came with the monitor to select the correct voltage.

Jumper Label:

JP1

Jumper Type:

3-pin header

Jumper Settings:

See

Table 4-4

Jumper Location:

See

Figure 4-15

The LVDS1 voltage selection jumper allows setting the voltage provided to the monitor

connected to the LVDS1 connector.

Setting

Description

Short 1-2

+3.3V LVDS (Default)

Short 2-3

+5V LVDS

Table 4-4: LVDS1 Voltage Selection Jumper Settings

Figure 4-15: LVDS1 Voltage Selection Jumper Location

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands