IEI Technology eKINO-BT Page 110 User Manual Download

Page: 110 / 157

eKINO-BT Mini-ITX SBC

Page 96

Manual Mode

The fan spins at the speed set in Manual Mode

settings.

Auto Mode

EFAULT

The fan adjusts its speed using Auto Mode

settings.

Auto mode fan start/off temperature

Use the + or – key to change the

Auto mode fan start/off temperature

value. Enter a

decimal number between 1 and 100.

Auto mode fan start PWM

Use the + or – key to change the

Auto mode fan start PWM

value. Enter a decimal

number between 1 and 100.

Auto mode fan slope PWM

Use the + or – key to change the

Auto mode fan slope PWM

value. Enter a decimal

number between 1 and 64.

5.3.4 RTC Wake Settings

The

RTC Wake Settings

menu (

BIOS Menu 9

) enables the system to wake at the

specified time.

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands